Section 33 Baggage Area
Page 33-2
Step 1: Cleco the F-1024-R Seat Floor to the F-1005A Rear Spar Bulkhead, and F-1018-R Outboard Rear Seat Rib, as shown in Figure 1.
Similarly, cleco the F-1024-L Seat Floor to the rear spar bulkheads and rear seat ribs on the left side.
Step 2: Match-Drill #40 the 3/32" nutplate attachment rivet holes along the inboard edge of the F-1024 Seat Floors into the underlying F-1017A Rear Seat Ribs.
Final-Drill #40 all remaining 3/32" nutplate attachment rivet holes in both seat floors.
Step 3: Final-Drill #19 the center screw holes in the four nutplate hole patterns along the inboard edge of both F-1024 seat floors.
Step 4: Except for the holes indicated in Figure 1, Final-drill #30 all the 1/8" holes in both seat floors.
Step 5: Cut two 16" lengths of AN257-P3 and remove the pins. Make the F-10103A-L and -R Lower Hinge Halves using the information given in Figure 2 (don't forget to remove the two eyes indicated in the figure) The Information is for the right hinge half, Save the pins and unused hinge halves they are used in Section 42.
Step 6: Locate the F-10103A-R right Lower Hinge Seat Half on the F-1022-R Baggage Floor as shown in Figure 2, then Match-Drill the holes of the seat floor into the hinge half using an 1/8" drill.
Repeat this step for the F-10101A-L Left Lower Seat Hinge half.
Step 7: Cleco the F-1022A-L and-R Baggage Floors to the F-1006B Bulkhead, the F-1023-L and-R Baggage Floor Angles, the F-1019, F-1020, and-1021 Baggage Ribs, and the F-1024-L and-R Seat Floors as shown in Figure 3.
Cleco the F-1013A Lower Seat Hinge Halves to the baggage floors and F-1034A Bulkhead.
Step 8: Final-Drill #40, deburr, and dimple the holes in the vertical flange of the two F-1023B Baggage Floor Angles that are common to the holes of the two F-1070 Mid Side Skins.
Cleco the baggage floor angles to the mid side skins and F-1022A Baggage Floors as shown in Figure 4
Step 9: Final -Drill #40 all of the 3/32"th holes along the inboard edge of the baggage floors common to the F-1019 Inbd Baggage Ribs.
The holes common to the F-1023B Baggage Floor Angles and F-1022A Baggage Floors
The row of holes common to both baggage floors and the F-1034A Bulkhead including the F-10103A Lower Seat Hinge Half.
.The row of holes along the forward edge of the F-1022A Baggage Floors common to the F-1024 Seat Floors.
Page 33-3
Step 2: Final-Drill #40 and dimple the holes in the F-1000B Baggage Door Shim and F-1026 Lower Baggage Door Seal Channel which are common to the F-1070-L and F-1073-L Side Skins. See Figure 2. The baggage door shim is not symmetrical, be sure to dimple it in the correct direction.
Step 3: Cleco the F_1026 Lower Baggage Door Seal Channel and the F-10100B Baggage Door Shim to the F-1070-L Side Skins as shown in Figure 2. Cleco the two end tabs of the lower baggage door seal channel to the F-1006A Bulkhead and the F-1022A-L Baggage Floor.
Step 4: There are two holes in the bottom end-tab of the F-1026 Lower Baggage Door Seal Channel. Match-Drill #30 the inboard holes into the F-1022A-L Baggage Floor and final drill the outboard holes.
Final-Drill the two holes common to the top end-tab of the lower baggage door seal channel and the F-1006A Bulkhead.
Step 5: Trim the shaded area shown in Figure 3 from the F-1031 Upper Baggage Door Channel
Step 6: Final-Drill #30 the holes in the outboard flange of the F-1031 Upper Baggage Door Seal Channel which is common to the outboard hole in the end tab of the F-1026 Lower Baggage Door Seal Channel. See Figure 4.
Step 7: Cleco the F-1031 Upper Baggage Door Seal Channel to the F-1006A Bulkhead and F-1026 Lower Baggage Door Seal Channel as shown in Figure 4.
Step 8: Cleco the F-1027 Close-Out Panel to the F-1026 Lower Baggage Door Channel Seal and the F-1006BA Bulkhead.
Step 9: Match-Drill #30 the holes in the lower flange of the F-a027 Close-Out Panel into the F-1022A-L Baggage Floor.
Final-Drill #30 the holes common to the vertical flange of the close-out panel and the F-1006A Bulkhead and the holes common to the holes-out panel and the F-1026 Lower Baggage Door Seal Channel.
Step 10: Final-Drill #30 the holes common to the F-1031 Upper Baggage Door Seal Channel and the F-1006A Bulkhead..