Section 33 Baggage Area
Page 33-7
Step 1: Install the nutplates shown in Figure 1 using the rivets called-out.
K-1100-8 along the Inboard Edges of both F-1022A
K-1000-08 8 Places along F-1006B
MS210051-L08 2 places along F-1006B
Step 2:Set the five rivets in the aft flange of both F-1022A Baggage Floors using the rivets called-out in Figure 1.
Step 2A: Rivet the two F-1023B Baggage Floor Angles to the F-1022A Baggage Floors and F-1070 Mid Side Skins using the rivets called-out in Figure 2.
Step 3: Rivet the F-1026 Lower Baggage Door Seal Channel and the F-10100B Baggage Door Shim to the F-1070-L and F-1073-L Side Skins using the rivets called-out in Figure 3.
Rivet the bottom end tab of the lower baggage door seal channel to the F-10022A-L Baggage Floor
and the top end-tab to the F-1006A Bulkhead using the rivets called-out in the figure. Do not set a rivet in the outboard hole of the top end-tab.
Step 4: Rivet the F-1031 Upper Baggage Door Seal Channel to the F-1006B Bulkhead and to the top end-tab of the F-1026 Lower Baggage Door Seal Channel using the rivets called-out in Figure 4.
Step 5: Rivet the F-1027 Close-out Panel to the F-1026 Lower Baggage Door Seal Channel, to the F-1022A-L Baggage Floor, and to the F-1006A Bulkhead using the rivets called-out in Figure 4.
Page 33-8
Step 1: Remove the tab from the top flange of the F-1080 Right Baggage Cover as indicated in the blowup of Figure 1 (for clarity the F-1034B Seat Back Brace is not shown}.
Step 2: Cleco the forward end of the F-1080 Right Baggage Cover to the F-1043C-R Fuselage Bulkhead.
Step 3: There are four holes in the forward flange of the F-1028 Baggage Bulkhead Channel. Draw a line down the entire flange centered on these holes, then dimple the holes for dimples in the F-1006D Bulkhead.
Step 4: Using the top two holes in the forward flange of the F-1028 Bulkhead Channel, cleco the flange to the F-1006D Bulkhead. Rivet the bottom end of the baggage bulkhead channel to the F-1029-R Bellcrank Rib using the rivets called out in the blow-up of Figure 1. (The top end is riveted after the Cabin Cover is installed in a later section.
Step 5: Cleco the Tailcone Forward Top Skin in place.
Step 6: Temporarily secure the bottom of the F-100F Lower Baggage Corrugation to the aft flange of the F-1022A Baggage Floors using crews called out in Figure 2.
Step 7: Match-Drill the holes along the left side of the F-1006F Lower Baggage Bulkhead Corrugation ( the right side is drilled later) into the F-1027 Close-Out Panel, the F-1031 Upper Baggage Door Seal Channel, and the F-1006A Bulkhead. Cleco a few of these holes to secure the lower baggage corrugation to the bulkhead.
Match-Drill the three holes of the lower baggage bulkhead corrugation into the F-1028 Baggage Bulkhead Channel. Be sure the line which was drawn on the forward flange of the baggage bulkhead channel remains centered in the holes of the lower baggage bulkhead corrugation while drilling.
Page 33-9
Step 1: If necessary, adjust the aft end of the F-1080 Right Baggage Cover so that it is aligned with the edge of the F-1006F Lower Baggage Bulkhead Corrugation. Match-Drill #30 the holes in the bottom flange of the right baggage cover into the F-102A-R Baggage Floor
then match-drill #30 the holes in the top flange into the F-1013-R Fwd Fuse Longeron.
Step 2: Match-Drill #19 the holes along the right edge if the F-1006 Lower Baggage Bulkhead Corrugation into the aft flange of the F-1080 Right Baggage Cover and into the F-1006C Bulkhead.
Step 3: Final-Drill #40 the nutplate attachment rivet holes common to the F-1080 Right Baggage Cover and the FF_1034C-R Fuselage Bulkhead.
Step 4: As shown in Figure 2, Cleco the F-1006E Upper Baggage Bulkhead Corrugation to the F-1006F Lower Baggage Bulkhead Corrugation.
Match-Drill #19 the holes of the upper baggage bulkhead corrugation into the F-1006A, C, and D Bulkheads.
Step 5: Remove the F-1006E and F Baggage Bulkhead Corrugations and the F-1074 Tailcone Forward Skin.
As shown in Figure 3, cleco the #19 hole in the aft flange of the F-1080 Right Baggage Cover. With the top and bottom flanges clecoed in place, Match-Drill #30 the three remaining 1/8" holes in the aft flange into the F-1006C Bulkhead.
Step 7: Match-Drill the nutplate attachment rivet holes, for the nutplates shown in Figure 3, into the F-1006C Bulkhead and into the F-1080 Right Baggage Cover.
.
Step 8: Remove the F-1080 Right Baggage Cover and deburr the holes in the baggage cover and all the accessible, corresponding holes in the other parts.
I also added some wire run corrugation to run wires behind the cover
Step 9: Dimple the #40 nutplate attachment river holes in the F-1080 Right Baggage Cover and the corresponding holes in the mating parts. Prime as/if desired.
Step 10: Rivet the F-1080 Right Baggage Cover to the F-1013-R Fwd Fuse Longeron, the F-1022A-R Baggage Floor, and the F-1006C Bulkhead using the rivets called-out in Figure 3.
Install all of the nutplates shown in Figure 3 using the rivets called-out.
Page 33-10
Step 1: Match-Drill #40 the nutplate attachment rivet holes for all the nutplates shown in Figure 1 into the F-1006A,C and D Bulkheads and into the F-21028 Baggage Bulkhead Channel. Deburr the holes.
Step 2: Dimple all of the nutplate attachment rivet holes drilled in Step 1
except for those associated with the F-1027 Close-Out Panel and the F-1031 Upper Baggage Door Seal Channel. Machine countersink the holes in these parts.
Step 3: Rivet the nutplates shown in Figure 1 to the F-1006A, C, and D Bulkheads and to the F-1028 Baggage Channel using the rivets called out.
Step 4: Modify the two sets of F-6114B and C Wear Blocks using using the dimensions given in.
Step 5: Cleco together the F-1006E and F Baggage Bulkhead.
Step 6: Center the F-6114B and C Wear Blocks on the shoulder harness cable notches in both sides of the F-1006E Baggage Bulkhead Corrugation.
Step 7: Match-Drill #30 the 1/8 holes of the F-6114B and C Wear Blocks into the F-1006F and E Baggage Bulkhead Corrugations respectively. Separate the baggage corrugations.
Step 8: Match-Drill #40 the nutplate attachment rivet holes, shown below the F-6114 Wear Blocks in Figure 4., into the F-1006F Lower Baggage Bulkhead Corrugation.
Step 9: Deburr the holes in the F-1006E and F Baggage Bulkhead Corrugations, dimple the #40 holes drilled in the previous step , and prime the parts.
Step 10: Rivet the nutplates shown in Figure 4 to both ends of the F-1006F Baggage Bulkhead Corrugations using the rivets called-out.
Step 11: Rivet the F-6114B Wear Block to the F-1006F Lower Baggage Bulkhead Corrugation using LP4-3 Blind Rivets, Install the rivets from the top of the wear block.
Step 12:Rivet the F-6114BCWear Block to the F-1006E Upper Baggage Bulkhead Corrugation using LP4-3 Blind Rivets, Install the rivets from the front of the baggage bulkhead corrugation, and back-up of the wear blocks with the washers shown.
