Step 5: Final-Drill #19 all the screw holes in the F-1051E Rear Tunnel Cover and F-1051F Baggage Tunnel Cover. Deburr the holes and edges in these covers.

Page 35-4

Step 1: Final-Drill #19 all the screw holes in the lower flange, forward flange,  and the aft flange of the F-1025-R Rear seat Cover Panel.

Step 2: Deburr then dimple the lower three screw holes in the forward flange of the F-1025-R Rear Seat Cover Panel for the head of an #8 screw. See Figure 1.

Step 3: Install the F-1025-R Rear Seat Cover Panel using the hardware ( except the upper flange hardware) called out in Figure 2.

Step 4: Match-Drill #19 the screw holes in the upper flange of the F-1025-R Rear Seat Cover {panel onto the F-1013-R Fwd Fuselage Longeron.

Step 5: Remove then deburr the holes and edges of the F-1025-R Rear Seat Cover Panel. Prime the rear seat cover panel if/as desired.

Step 6: Using a nut plate as a drill guide match-drill #40 the nutplate attach pattern into the F-1013-R Fwd Fuselage Longeron at each of the seven locations match drill in Step 4.

Machine countersink these holes for the head of an AN426AD3 rivet on the upper side of the longerons. Deburr all the holes in the longerons drilled in this step and Step 4.

Install nutplates to the longerons per the callouts in Figure 1.

Page 35-5

Step 1:  Cleco the F-1051C Aft Fuselage Tunnel Cover and F-1051G Splice plate together shown in Figure 1.

Step 2:  Final-Drill #40 the holes common between the parts clecoed together in Step 1 and both sets of nutplate attach holes along the forward edge of the F-1051C Aft Fuselage Cover.

Final Drill #19 the both screw holes along the forward edge of the splice plate. Final Drill #19 all the screw holes along the side and aft flanges of the F-1051C Aft Fuselage Tunnel Cover.

Step 3: Disassemble and deburr all parts. Dimple (flush head on top side) the rivet holes in all the parts. Dimple the screw holes in the F-1051C Aft Fuselage Tunnel Cover and the F-1015G Splice Plate for the head of an #8 screw. Dimple the nutplates. Prime parts if desired.

Step 4: Repeat Step 1 then rivet the parts clecoed together in step 1. This will create the Aft Tunnel Cover Assembly.

Step 5: Final-Drill #19 the screw holes along the edge and side flanges of the F-1015A Fwd Fuselage Tunnel Cover for the head of an #8 screw. Prime the fwd fuselage tunnel cover in desired.

Page 35-6

Step 1:  Figure 1 shows the final installation of the tunnel covers, but wait to install them until all systems have been installed in the tunnel.

Page 35-7

Step 1: Final-Drill #19 the screw holes in the F-1016E-L Flap Torque Tube Cover.

Step 2: Deburr the holes ad edge of the F-1016E-L Flap Torque Tube Cove> Dimple the screw holes in the flap torque tube cover for the ed of an #8 screw.

Step 3: Final Drill #19 the holes in the F-1042G-R Wire Cover

Step 4: Deburr the holes and edges of the F-1042G-R Wire Cover. Prime the cover if desired.

Page 35-8

NOTE: When installing the F-1067A Seat Floors, first slide the cover up underneath the F-1043B Forward Fuselage Bulkhead.

Step 1: Figure 1 shows the final install of the F-1067A Seat Floors, but wait to install them until all systems installations and wiring runs have been completed.

Page 35-9

Step 1: Final-Drill #19 the screw holes in the F-1015D-R Mid Cabin Side Cover and F-1067B Seat Floor Cover. Final-Drill #40 the nutplate attach holes in the mid cabin side cover.

Step 2: Deburr the holes and edges of both the F-1015D-R Mid Side Cover and F-1067B Seat Floor cover. Dimple all the screw holes in the mid cabin side cover except the top row of holes and holes in the forward lower flange (See Figure 1) Dimple the plate nuts. Prime the parts.

Step 3: Rivet the plate nuts to the F-1015D-R Mid Side Cover per the callouts in Figure 1.

Note: When installing the F-1015D Mid Cabin Covers, first slide them up underneath the F-1015C Mid Cabin Decks then slide the cover down underneath the F1016 Outbd Foot Well Rib.

Page 35-10

Note: This page describes the installation of a F-1050B Bolt Access Plate and VENT SV-1 Remote Vent to the right side of the aircraft. The left installations are a mirror of the right.

Step 1:  Final-Drill #19 the screw holes in the F-1050B Bolt Access Plate.

Step 2: Deburr the edges of the F-1050B Bolt Access Plate. Prime if desired. See Figure 1 for installation of the bolt access plate.

Step 3: Mix and apply tank sealant to the flange around the VENT SV-1 Remote Vent. Center the vent in the NACA shaped cutout in the F-1069-R Forward Side Skin then clamp the vent in place and let the tank sealant cure. See Figure 1.

Picture of inside metal painted Nevada Beige